Key contact: Wendy She
Tel: 0086-574-88060400
Fax: 0086-574-88060200
www.ruicancasting.com
sales@cnsandcasting.com
Ruican Machinery >> Sand Casting

Sand Casting

Sand casting, the most widely used casting process, utilizes expendable sand molds to form complex metal parts that can be made of nearly any alloy. Because the sand mold must be destroyed in order to remove the part, called the casting, sand casting typically has a low production rate. The sand casting process involves the use of a furnace, metal, pattern, and sand mold. The metal is melted in the furnace and then ladled and poured into the cavity of the sand mold, which is formed by the pattern. The sand mold separates along a parting line and the solidified casting can be removed. The steps in this process are described in greater detail in the next section. In sand casting, the primary piece of equipment is the mold, which contains several components. The mold is divided into two halves - the cope (upper half) and the drag (bottom half), which meet along a parting line. Both mold halves are contained inside a box, called a flask, which itself is divided along this parting line. The mold cavity is formed by packing sand around the pattern in each half of the flask. The sand can be packed by hand, but machines that use pressure or impact ensure even packing of the sand and require far less time, thus increasing the production rate. After the sand has been packed and the pattern is removed, a cavity will remain that forms the external shape of the casting. Some internal surfaces of the casting may be formed by cores.

Sand casting is used to produce a wide variety of metal components with complex geometries. These parts can vary greatly in size and weight, ranging from a couple ounces to several tons. Some smaller sand cast parts include components as gears, pulleys, crankshafts, connecting rods, and propellers. Larger applications include housings for large equipment and heavy machine bases. Sand casting is also common in producing automobile components, such as engine blocks, engine manifolds, cylinder heads, and transmission cases.

Sand casting is able to use of almost any alloy. An advantage of sand casting is the ability to cast materials with high melting temperatures, including steel, nickel, and titanium. The four most common materials that are used in sand casting are shown below, along with their melting temperatures

Materials              Melting temperature   
Aluminum alloys     1220 °F (660 °C)   
Brass alloys           1980 °F (1082 °C)   
Cast iron               1990-2300 °F (1088-1260 °C)   
Cast steel              2500 °F (1371 °C)   

The material cost for sand casting includes the cost of the metal, melting the metal, the mold sand, and the core sand. The cost of the metal is determined by the weight of the part, calculated from part volume and material density, as well the unit price of the material. The melting cost will also be greater for a larger part weight and is influenced by the material, as some materials are more costly to melt. However, the melting cost in typically insignificant compared to the metal cost. The amount of mold sand that is used, and hence the cost, is also proportional to the weight of the part. Lastly, the cost of the core sand is determined by the quantity and size of the cores used to cast the part.

Sand casting process advantages
Can produce very large parts
Can form complex shapes
Many material options
Low tooling and equipment cost
Scrap can be recycled
Short lead time possible

Applications:
Engine blocks and manifolds, machine bases, gears, pulleys, agriculture parts,marine parts,medical parts,hardware, automobile parts,ect.

  • The Sand Casting process -Ruican Green Sand Mold process - is commonly used in the casting of aluminum, brass/bronze, and iron products.

  • Process:Green sand castingMaterial: Ductile Iron-GGG50Used for: Engine blocks and manifolds, machine bases, gears, pulleys, agriculture parts,marine parts, medical parts,lifting machine parts;
  • Aluminum Castings is a full service aluminum casting mould and aluminum casting foundry. We specialize in providing aluminum sand castings, aluminum dry sand castings.

  • Aluminum casting Process are classified as Ingot casting or Mould casting. During the first process, primary or secondary aluminium is cast into rolling ingot (slab), extrusion ingot (billet) and wire bar ingot which are subsequently transformed in semi- and finished products.
  • Aluminum gravity casting and sand casting process is better to avoid porosity inside casting after secondary machining. Gravity casting part is nice looking with better surface than sand casting.

  • Process: Aluminium gravity castingMaterial: aluminiumMachine: die-machine with 1200TUsed for: Engine blocks and manifolds, machine bases, gears, pulleys, agriculture parts,marine parts, medical parts
  • Ductile iron casting : Auto part High quality ductile iron castings made by hot mold system used for auto and other fields

  • Process: Aluminium gravity castingMaterial: AlSi9Cu3Used for: Engine blocks and manifolds, machine bases, gears, pulleys, agriculture parts,marine parts, medical parts,lifting machine parts; hardware
  • The sand casting process involves the use of a furnace, metal, pattern, and sand mold. The metal is melted in the furnace and then ladled and poured into the cavity of the sand mold.

  • Material: Grey Iron (GG15;GG20;GG25;GG30;GG35;GG40; GG45.etc.) Used for Agricultural machines; lifting machines; grinding machines; medical machines,automobile cars,ect.
  • Brass sang casting, as the name suggests, involves the use of brass as the molten metal. Brass casting can be carried out by the way of brass sand casting only.

  • Process: Brass sand castingMaterial: C26800;C27000;C27200;C27400,ECT.Used for: Engine blocks and manifolds, machine bases, gears, pulleys, agriculture parts,marine parts, medical parts
© 2013 Ningbo Ruican Machinery Company    Site Design & SEO by 86001.cn
If you need some casting or machined part OEM or aftermarket, REICAN will be the best choice for you.